What 12V, 18V and 20V MAX really mean, whether brushless is worth it, how to size a battery, and when you need a hammer drill or rotary hammer.
The Review NYU is not affiliated with New York University.
We do not currently earn a commission from any link on this page. If links ever become affiliate links, we will label them clearly.
Short answer. For most home projects, buy an 18V or 20V MAX drill/driver; Lowe's says that class meets most home needs, while 12V drills suit light jobs like shelves and furniture. "20V MAX" is the battery's maximum unloaded voltage and, by DeWalt's own fine print, equals 18V nominal, so the two are the same class. Brushless motors give more runtime and durability for more money, and higher amp-hour (Ah) batteries run longer but weigh more. Pick your battery brand carefully, because batteries rarely cross brands. Add a hammer drill for brick, block and occasional concrete, and use an SDS rotary hammer for heavier concrete work.
This is a research-based guide, not a hands-on test. The Review NYU did not test any drill, battery or hammer drill for this article. On 17 November 2026 we read the cordless drill buying guides from Lowe's and Home Depot, Consumer Reports' 2026 cordless drill ratings page (which describes its own lab tests), and two Family Handyman explainers: hammer drill vs. rotary hammer and impact driver vs. drill. For the 18V vs. 20V MAX labelling question we relied on search excerpts from two third-party pages that quote DeWalt's battery disclaimer; we did not read a DeWalt page directly.
Retailers sell the tools they describe, so we treat their advice as background, not neutral evidence. Consumer Reports' findings are its own measurements.
Three cordless tools look alike but do different jobs, and the type matters more than any spec on the box.
A standard drill (often sold as a drill/driver) spins a bit held in a chuck. Family Handyman calls it the better tool for boring holes and for jobs needing adjustable torque, such as furniture assembly. For most first-time buyers, this is the one to get.
A hammer drill adds a forward pounding motion while the bit turns, which Home Depot says makes drilling into masonry and other hard surfaces easier. On most models the hammer mode can be switched off, so it also works as an ordinary drill.
An impact driver is built to drive fasteners. According to Family Handyman, it uses an internal hammer-and-anvil mechanism that delivers bursts of torque up to 50 times a second, and takes 1/4-inch hex bits instead of a chuck. It suits decks and other jobs with many long screws, but the same source says it is not a drill replacement.
A summary of what the sources say each tool is for, including the rotary hammer covered further down.
| Tool | Bit holder | Best for | Weak at | Source |
|---|---|---|---|---|
| Drill/driver | Three-jaw chuck (3/8 or 1/2 in.) | Holes in wood, metal, drywall; assembling furniture; occasional screws | Lots of long screws; repeated masonry holes | Family Handyman, Home Depot |
| Hammer drill | Three-jaw chuck | Brick, mortar, concrete block; the occasional hole in poured concrete | Many or large holes in hard concrete | Family Handyman |
| Impact driver | 1/4-in. hex quick-release | Decks, subfloors, lag bolts, many long screws | Precise holes; jobs needing gentle, adjustable torque | Family Handyman |
| Rotary hammer | SDS-Plus (larger: SDS-Max) | Hardened concrete, larger holes, chiseling tile or mortar in hammer-only mode | General woodworking; heavier and costlier than a drill | Family Handyman, Home Depot |
The sources do not fully agree on where to draw the line. Home Depot's guide says 12-volt models are "great for general purpose use around the house" and that 18 volts is the most common rating, while Lowe's points most homeowners to 18 or 20 volts. If you expect larger holes or bigger projects, 18V/20V is the safer pick.
Lowe's explains that a "max" voltage rating is the maximum voltage the battery delivers when the drill is not drilling or driving. DeWalt's own disclaimer, as quoted on a third-party battery page and summarized by another explainer, states that the maximum initial battery voltage measured without a workload is 20 volts and the nominal voltage is 18. So a 20V MAX tool and an 18V tool are the same class; "20" does not mean more power. Check the fine print for the brand you choose.
The practical differences, according to the guides we read:
Both claims compare otherwise similar tools, so treat "brushless" as one factor, not a guarantee. For occasional use, brushed is usually adequate.
Home Depot defines amp-hours as the battery's energy capacity: a higher number means longer operating time, and it gives the example that a 3.0Ah lithium-ion battery lasts twice as long as a 1.5Ah one. It also says the higher-capacity pack is heavier, so if weight matters, a smaller battery plus a spare can be a better setup. Lowe's adds that voltage and amp-hours work together: a high-voltage, low-Ah battery has power but shorter runtime, and the reverse gives runtime with less power.
Charge times vary: Lowe's says 20-volt, 1.5Ah batteries take 30 to 60 minutes, and Consumer Reports reports one budget 24-volt model took around 85 minutes.
Batteries generally fit only the same brand's line, so your first drill decides your later cordless tools. Lowe's suggests looking for drills whose batteries are shared with other power tools and even lawn tools, and Family Handyman advises existing cordless owners to check whether their brand makes a hammer drill or rotary hammer on the same batteries. Check that the tools you want next are on the same battery.
The chuck size is the largest bit shank the drill can hold. Home Depot says 3/8 inch is the most common size on general-use drills and covers most bits, while more powerful drills use a 1/2-inch chuck for heavy-duty work. Consumer Reports notes that 3/8-inch chucks on compact 12-volt drills cannot take the largest bits. For masonry, Family Handyman says keyless chucks often lack holding power.
The numbered ring behind the chuck is the clutch. Home Depot explains that it limits torque so you do not over-drive or strip screws: lower settings are for screwing, higher settings for drilling at full strength.
Speed is measured in revolutions per minute (RPM). Home Depot says most drills have a variable-speed trigger and a reverse switch, and recommends faster speeds for drilling wood and slower speeds for driving screws. Consumer Reports says most drills in its ratings have two speed settings.
Torque is the turning force a drill can apply. Brands publish torque figures, but the sources we read do not describe a shared test method behind them, so a higher number from one brand may not mean more real-world force than a lower number from another. Consumer Reports sidesteps this by clamping each drill to a dynamometer and measuring RPM and torque itself, then turning those readings into speed and power scores. Independent results like these are more useful than the box.
Drills are sold as kits (tool, one or two batteries, charger, often a bag or case) or as a "bare tool" with no battery or charger.
Before buying a holiday bundle, see how to tell if a sale is a real deal.
If you only work in wood, drywall and metal, you do not need a hammer drill.
Family Handyman puts top-tier rotary hammers at $400 to $800, or about $60 a day to rent, so renting suits a one-off job. An impact driver is not a substitute for either tool.
For most homes, an 18V/20V MAX drill/driver kit with two batteries on a brand platform you are happy to stay with is the safest choice. Choose 12V if weight matters more than power. Add a hammer drill if you regularly drill brick or block, and rent or buy an SDS rotary hammer only for serious concrete work. For help reading the numbers on the box, see how to read a product spec sheet.
Not by the label alone. DeWalt's disclaimer, as quoted by third-party sites, says 20V MAX is the maximum initial voltage without a load and the nominal voltage is 18, so the two are the same class.
For light jobs such as assembling furniture or hanging shelves, Lowe's and Consumer Reports say yes. If you plan to bore large holes through studs or drive many long screws, an 18V or 20V MAX drill is the better fit.
For a hole or two, Family Handyman says a regular drill with a masonry bit can work. For regular work in brick, mortar or block, a hammer drill is much faster, and for hard concrete or many large holes a rotary hammer is better.
No. Family Handyman says impact drivers excel at driving screws and bolts but lack the adjustable torque and precision of a drill.
Home Depot says a 3.0Ah battery runs about twice as long as a 1.5Ah one but is heavier. A 2Ah battery keeps the drill light; 4Ah or more suits long sessions.